Inovonics EN1260 Uživatelský manuál stáhnout pdf

EN1260 EchoStream® Passive Infrared Motion

Detector

Installation and Operation Manual - 05379D

1 Overview

The EN1260 is a low-current motion detector highly sensitive to moving heat (infrared

radiation) sources. It features increased immunity to radio frequency interference,

vibration, static, lightning, ambient temperature changes, and other common causes

of false alarms.

The EN1260 includes a range of features, including a wall tamper capability for

increased security, and a fixed or variable sleep time option for normal or high-traffic

applications.

Caution: The EN1260 needs one minute for stabilization after power up. During the

stabilization period, the LED will blink twice per second, and the EN1260 will not be

operational.

1.1 Inovonics Wireless Contact Information

If you have any problems with this procedure, contact Inovonics Wireless technical

services:

• E-mail: support@inovonics.com

• Phone: (800) 782-2709; (303) 939-9336

EN1260 Components

Figure 1 EN1260 components

2 Installation and Startup

2.1 Install/Replace Battery

To install the battery:

1. Use a small Phillips screwdriver to remove the screw at the bottom of the EN1260

housing; separate the housing.

2. Install/replace the battery.

3. Press the Reset button to initialize the transmitter.

2.2 Select Frequency Band

EchoStream products are able to use a range of radio frequencies, and must be

configured for your geographic area. To configure the EN1260:

1. Place a selection jumper on the appropriate frequency band selection pins (Fig.

1).

• Place the jumper on the left two pins to select 915-928 MHz for Australia.

• Place the jumper on the right two pins to select 921-928 MHz for New Zealand.

• Leave the jumper off the pins to select 902-928 MHz for North America.

2. Press the Reset button.

Caution: When pressing the Reset button, make sure you don’t also touch the

frequency band selection pins. Touching the frequency band selection pins while

pressing the Reset button can inadvertently set the EN1260 to the wrong frequency

band.

2.3 Select PIR Sensitivity

The pulse count jumper setting provides control for normal or difficult operating

environments. Automatic pulse count is recommended for reliable operation in

environments subject to temperature fluctuations that may cause false alarms. The

single pulse count mode is more sensitive to minor temperature variations, and should

be used in sites where variant heat sources will not cause false alarms. Automatic

pulse count is the factory default because it allows more reliable operation in

environments subject to temperature fluctation. To select PIR sensitivity:

1. Place a selection jumper on the appropriate pulse count selection pins.

• Place the jumper on the left two pins to select automatic pulse count.

• Place the jumper on the right two pins to select single pulse count.

2. Press the Reset button to complete configuration.

2.4 Select Fixed/Variable Sleep Time

The sleep time jumper setting provides control for normal or high-traffic operating

environments. When set to fixed, if the EN1260 senses motion, it will transmit an

alarm, then enter sleep mode for 180 seconds; if motion is sensed when the sleep

time has expired, the EN1260 will transmit another alarm. Fixed sleep time is

recommended for normal operating environments. When set to variable, if the

EN1260 senses motion, it will transmit an alarm, then enter sleep mode for 180

seconds; if motion is sensed before the sleep time has expired, the EN1260 will restart

the 180 second interval. Variable sleep time is recommended for high-traffic operating

environments.

1. Place a selection jumper on the appropriate sleep time selection pins.

• Place the jumper on the left two pins to select fixed sleep time.

• Place the jumper on the right two pins to select variable sleep time.

2. Install the battery.

3. Press the Reset button.

2.5 Register the Transmitter

The EN1260 must be registered with the system receiver in order to be monitored and

supervised. Each EN1260 has a unique factory-programmed identification number.

Refer to the receiver, network coordinator or control panel installation instructions for

details on registering a transmitter.

1. When prompted reset the EN1260, press the EN1260 Reset button.

2. Replace the EN1260 cover.

Caution: The EN1260 should be tested after registration to ensure operation. To test

the EN1260, activate each of the conditions and ensure an appropriate response.

Note: The EN1260 retains programming data in non-volatile memory. It does not

require re-programming after loss of power.

2.6 Mount the Transmitter

Mount the transmitter.

1. Remove the EN1260 printed circuit board from the housing.

2. Use the included hardware to mount the EN1260 housing back plate to the

mounting surface.

a. If using the wall tamper function for increased security, mount the housing back

plate per Figure 2, ensuring the tamper switch is depressed..

Figure 2 EN1260 mounting back plate

b. If not using the wall tamper, mount the housing back plate using all appropriate

hardware.

A Frequency band

selection pins

B Reset button C Pulse count selection

pins

D Tamper switch E Test mode reed switch F Sleep time selection

pins

Mount either

corner or wall with

screw only

Mount either corner

or wall with screw

and wall anchor

Mount either

corner or wall with

screw only

1 2

Shrnutí obsahu

Strany 1 - Detector

Strany 2 - 4.2 Lens Options

Komentáře k této Příručce

Žádné komentáře

Inovonics EN1260 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Senzory Inovonics EN1260. Inovonics EN1260 User Manual Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Senzory Inovonics EN1260