Inovonics EN1941 Uživatelský manuál stáhnout pdf

4.9.13 06287E © Inovonics, 2013 - www.inovonics.com

EE1941/EN1941 One-Way Binary RF Module

Installation and Operation Manual - 06287E

1 Overview

EchoStream RF modules are designed to be easily interfaced with your

electronic remote application controller (RAC). RF modules allow the

assimilation of any user-specific application into an EchoStream system.

Once integrated with existing products, RF modules provide you with

complete EchoStream functionality.

E*1941 one-way binary RF modules are end-devices that use a logic-level

connection to interface with your RAC. E*1941 one-way binary RF modules

can be used in either one-way or two-way EchoStream systems.

Figure 1 One-Way System Components

2 One-Way Binary RF Module Components

The E*1941 is a universal one-way binary RF module with two alarm input

pins, allowing the use of dual inputs. Input one is the primary alarm, bit 0;

input two is the secondary alarm, bit 1.

There are two models in the E*1941 product family.

• The EN1941, for 900 MHz applications in North America, New

Zealand, and Australia,

• The EE1941, for 868 MHz applications in Europe

Figure 2 EN1941 One-Way Binary RF Module Components

Figure 3 EE1941 One-Way Binary RF Module Components

Frequency band selection pins (EN1941 only) Place a jumper to select the

frequency band for your geographic area.

• Place the jumper on the left two pins to select 915-928 MHz for

Australia.

• Place the jumper on the right two pins to select 921-928 MHz for New

Zealand.

• Leave the jumper off the pins to select 902-928 MHz for North

America.

ES selection pins (EE1941 only) To enable compatibility with ES products,

place a selection jumper on the ES selection pins; if no ES products are

used in your system, remove the selection jumper.

N/O selection pins Place a jumper to select normally open inputs; remove

the jumper to select normally closed.

Note: The E*1941 is shipped with the jumper unattached. With the jumper

unattached, the E*1941 defaults to normally closed.

Secondary alarm Connects a secondary end-device to provide RF alarm

data for any user-specific application.

Primary alarm Connects a primary end-device to provide RF alarm data for

any user-specific application.

Tamper input Connects a tamper input to send a message when user-

specific end-device is tampered with.

Reset input Connects a reset input to reset the one-way binary RF module

after a frequency band selection change or N/O - N/C selection change,

and to initiate an RF transmission.

Power Connect power cabling to an external power supply of 2.4 to 5.5

volts.

Ground Connects to ground.

Mounting hole Used to mount the one-way binary RF module to the user-

specific product. The mounting hole should only be used with a nylon

standoff, never metal.

LED contacts Use to control an LED switch. Not designed to drive LED

power.

Board stabilization holes Used to mount and stabilize the board. The board

stabilization holes should only be used with non-metal standoffs.

A Board stabilization hole. B Reserved C Reserved

D Secondary alarm E Power F Ground

G Primary alarm H LED contacts I Tamper input

J Reset input K Frequency band

selection pins

L N/O selection pins

M Mounting hole N On-board antenna O Board stabilization

hole

A Board stabilization hole. B Reserved C Reserved

D Secondary alarm E Power F Ground

G Primary alarm H LED contacts I Tamper input

J Reset input K ES selection pins L N/O selection pins

M Mounting hole N On-board antenna O Board stabilization

hole

1 2 3 4 5

Shrnutí obsahu

Strany 1 - 1 Overview

4.9.13 06287E © Inovonics, 2013 - www.inovonics.comEE1941/EN1941 One-Way Binary RF ModuleInstallation and Operation Manual - 06287E1 OverviewEchoStrea

Strany 2 - 5 Installation

4.9.13 06287E © Inovonics, 2013 - www.inovonics.com 23 One-Way Binary RF Module Dimensions Figure 4 E*1941 One-Way Binary RF Module Dimensions4 One-

Strany 3 - 9 Warranty and Disclaimer

4.9.13 06287E © Inovonics, 2013 - www.inovonics.com 37 Compliance Requirements7.1 UL and cUL Requirements The EN1941 Module holds a UL and cUL Recogn

Strany 4 - Review Form

4.9.13 06287E © Inovonics, 2013 - www.inovonics.com 4Inovonics One-Way Binary RF Module Compliance Review FormPlease provide the following informatio

Strany 5 - Inovonics approval

4.9.13 06287E © Inovonics, 2013 - www.inovonics.com 5Required materials from Inovonics• The record of product sample review and test, as necessaryIno

Příbuzné modely EE1941

Komentáře k této Příručce

Žádné komentáře

Inovonics EN1941 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Senzory Inovonics EN1941. Inovonics EN1941 User Manual Uživatelská příručka

Shrnutí obsahu

Příbuzné modely EE1941

Komentáře k této Příručce

Související produkty a manuály pro Senzory Inovonics EN1941